Hardware Parts for the Rosetta

Building a Rosetta: 1. Parts · 2. Common build steps · 3a. With the Rosetta PCB · 3b. Without the PCB · 4. Software


This is the one parts list for both ways of building a Rosetta. The Applies to column says which build each part is for:

Both Needed for either build.
Rosetta PCB Only when building with the Rosetta circuit board - see Hardware Build With Rosetta PCB.
Without PCB Only when building without it, using breakout boards - see Hardware Build Without PCB.

Without the PCB, the case and power parts (1000 - 1199 and 2000 - 2199) are the builder's own choice, so they are listed for the Rosetta PCB build only.

The expansion box (part numbers 2000 - 2499) is optional. Part numbers stay the same whichever build is chosen.

# Item Qty Source Source P/N Applies to Comments
Base Box
########## Base Box - Case ##########
1000 Case
1001 Case 1     Rosetta PCB  
########## Base Box - Power ##########
1100 Power
1101 Power Switch 1 Astrodyne TDI 082M.01001.00-LS Rosetta PCB  
1102 Power Cord 1 Schurter 6009.1214 Rosetta PCB  
1102 Power Cord 1     Without PCB Use the appropriate power cord for where you will be powering this.
1103 Power Outfeed Jack 1 Schurter 6600.4315 Rosetta PCB  
1111 24 VDC Power Supply 1 MeanWell LRS 100-24 Both  
1112 24 VDC to 5 VDC power module 1     Both Powers both the Raspberry Pi and the Mesa card.
1121 110 VAC power cable, #14 1     Both  
1122 24 VDC power cable, #26       Both  
########## Base Box - Electronics ##########
1200 Electronics Inside the Box
1201 Raspberry Pi 5
  • 8 GB RAM
  • 128 GB microSD card
1 CanaKit PI5-8GB-STR128-C4-BLK Both  
1210 Mesa 7i92TH Anything I/O Ethernet card 1 Mesa US 7i92TH Both The base card. Its address is 10.10.10.10.
1220 Stepper Motor Drivers 6 Stepper Online DM542T Both Channels 00 - 05. be sure to use high quality drivers; the ones from Stepper Online are recommended.
1230 Rosetta PCB 1     Rosetta PCB The same PCB is used in both boxes; the expansion box's has fewer parts fitted.
1240 Ethernet switch, gigabit, unmanaged 1     Both Only the Raspberry Pi and the Mesa cards are connected to it.
1250 IDC26 breakout board (26 screw terminals, DIN rail) 2 Jienk (Amazon) B0CBV9NDJY Without PCB One for each of the base card's headers, P1 and P2. See Hardware Build Without PCB.
1260 Relay module, 1 channel, 5 VDC coil, low-level trigger 3     Without PCB Relay Modules 1, 2 and 3: one each for the red light, the green light and the siren - only if a signal tower is used. Each must switch on when its input is pulled low. The Rosetta PCB has these relays built in. See Signal Tower Relays.
########## Base Box - Panel Mount Parts ##########
1300 Panel Mount Parts
1301 GX-16/4 stepper motor jacks 6     Both Channels 00 - 05
1302 GX-12/2 limit switch jacks 3     Both Limit Jacks 1 - 3
1303 GX-16/2 E-stop button jack 1     Both Optional E-stop button
1304 GX-12/4 signal tower jack 1     Both Optional signal tower
########## Base Box - Cables ##########
1400 Cables within the Box
1401 IDC26-IDC26 Ribbon Cable 2     Both  
1402 IDC6-IDC6 Ribbon Cable 12     Rosetta PCB 2 for each stepper motor driver
1403 Ethernet cable (CAT-6 minimum, CAT-8 recommended) 2     Both Raspberry Pi to switch, and switch to the base card
1404 Hookup wire, 22 AWG, stranded     Without PCB From the breakout boards to the DM542T drivers, jacks and relay module.
Expansion Box (optional)
########## Expansion Box - Case ##########
2000 Case
2001 Case 1     Rosetta PCB  
########## Expansion Box - Power ##########
2100 Power
2101 Power parts: a 24 VDC supply for the 4 drivers, and a 5 VDC supply for the expansion card To be confirmed     Rosetta PCB  
########## Expansion Box - Electronics ##########
2200 Electronics Inside the Box
2210 Mesa 7i92TH Anything I/O Ethernet card 1 Mesa US 7i92TH Both The expansion card. Its address is 10.10.10.11.
2220 Stepper Motor Drivers 4 Stepper Online DM542T Both Channels 06 - 09
2230 Rosetta PCB 1     Rosetta PCB The same PCB as the base box (1230), with fewer parts fitted - see Hardware Build With Rosetta PCB.
2250 IDC26 breakout board (26 screw terminals, DIN rail) 1 Jienk (Amazon) B0CBV9NDJY Without PCB For the expansion card's P2 (its P1 isn't used).
########## Expansion Box - Panel Mount Parts ##########
2300 Panel Mount Parts
2301 GX-16/4 stepper motor jacks 4     Both Channels 06 - 09
2302 GX-12/2 limit switch jacks 3     Both Limit Jacks 4 - 6
########## Expansion Box - Cables ##########
2400 Cables within the Box
2401 IDC26-IDC26 Ribbon Cable 1     Both  
2402 IDC6-IDC6 Ribbon Cable 8     Rosetta PCB 2 for each stepper motor driver
2403 Ethernet cable (CAT-6 minimum, CAT-8 recommended) 1     Both Expansion card to the switch in the base box
2404 Hookup wire, 22 AWG, stranded     Without PCB From the breakout board to the DM542T drivers and jacks.
Other
########## Other ##########
1900 Other
1901 Computer Monitor (1920x1080) 1 LG 24MR400-B.AUSQ Both  
1902 Keyboard & Mouse 1 Kensington K72436AM Both  

Next: 2. Common build steps

########## Standard Footer for all pages ##########
 

About the Rosetta System
Terms of Use

eMail comments to
ColvinTools @ Gmail [period] com -> mailto:ColvinTools [snail] Gmail [period] com